EGVV65B-FL-C3-4XR
8-port sector antenna, 2x 694–862, 2x 880–960 and 4x 1695–2690 MHz, 65° HPBW, 4x RET. Low band arrays are diplexed at the element level.
Features and Benefits
- All Internal RET actuators are connected in “Cascaded SRET” configuration
- Uses the 4.3-10 connector which is 40 percent smaller than the 7-16 DIN connector
Specifications
General Specifications
| Antenna Type | Sector |
| Band | Multiband |
| Grounding Type | RF connector inner conductor and body grounded to reflector and mounting bracket |
| Performance Note | Outdoor usage |
| Radome Material | Fiberglass, UV resistant |
| Radiator Material | Aluminum | Low loss circuit board |
| Reflector Material | Aluminum |
| RF Connector Interface | 4.3-10 Female |
| RF Connector Location | Bottom |
| RF Connector Quantity, high band | 4 |
| RF Connector Quantity, low band | 4 |
| RF Connector Quantity, total | 8 |
Remote Electrical Tilt (RET) Information
| RET Interface | 8-pin DIN Female | 8-pin DIN Male |
| RET Interface, quantity | 1 female | 1 male |
| Input Voltage | 10–30 Vdc |
| Internal RET | High band (2) | Low band (2) |
| Power Consumption, idle state, maximum | 2 W |
| Power Consumption, normal conditions, maximum | 13 W |
| Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
| Width | 350 mm | 13.78 in |
| Depth | 208 mm | 8.189 in |
| Length | 1850 mm | 72.835 in |
| Net Weight, without mounting kit | 30.5 kg | 67.241 lb |
Array Layout
| Click on image to enlarge. |
Electrical Specifications
| Impedance | 50 ohm |
| Operating Frequency Band | 694 – 862 MHz | 880 – 960 MHz | 1695 – 2690 MHz |
| Polarization | ±45° |
| Total Input Power, maximum | 800 W @ 50 °C |
Electrical Specifications
| Frequency Band, MHz | 694–862 | 880–960 | 1695–1920 | 1920–2180 | 2300–2500 | 2500–2690 |
| Gain, dBi | 15.2 | 15.5 | 18.2 | 18.9 | 18.8 | 18.8 |
| Beamwidth, Horizontal, degrees | 67 | 62 | 60 | 61 | 60 | 59 |
| Beamwidth, Vertical, degrees | 11.8 | 9.8 | 5.6 | 5 | 4.4 | 4.3 |
| Beam Tilt, degrees | 2–14 | 2–14 | 2–12 | 2–12 | 2–12 | 2–12 |
| USLS (First Lobe), dB | 16 | 19 | 19 | 20 | 18 | 19 |
| Front-to-Back Ratio at 180°, dB | 29 | 29 | 31 | 36 | 36 | 37 |
| Isolation, Cross Polarization, dB | 28 | 28 | 28 | 28 | 28 | 28 |
| Isolation, Inter-band, dB | 30 | 30 | 30 | 30 | 30 | 30 |
| VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc | -150 | -150 | -150 | -150 | -150 | -150 |
| Input Power per Port at 50°C, maximum, watts | 200 | 200 | 250 | 250 | 250 | 200 |
Electrical Specifications, BASTA
| Frequency Band, MHz | 694–862 | 880–960 | 1695–1920 | 1920–2180 | 2300–2500 | 2500–2690 |
| Gain by all Beam Tilts, average, dBi | 14.9 | 15.3 | 17.6 | 18.4 | 18.4 | 18.4 |
| Gain by all Beam Tilts Tolerance, dB | ±0.4 | ±0.3 | ±0.8 | ±0.5 | ±0.6 | ±0.7 |
| Gain by Beam Tilt, average, dBi | 2 ° | 14.9 8 ° | 14.914 ° | 14.8 | 2 ° | 15.5 8 ° | 15.314 ° | 15.0 | 2 ° | 17.3 7 ° | 17.712 ° | 17.7 | 2 ° | 17.9 7 ° | 18.512 ° | 18.5 | 2 ° | 18.0 7 ° | 18.612 ° | 18.4 | 2 ° | 17.9 7 ° | 18.612 ° | 18.4 |
| Beamwidth, Horizontal Tolerance, degrees | ±1.3 | ±2.6 | ±4.4 | ±3.2 | ±4.7 | ±3.2 |
| Beamwidth, Vertical Tolerance, degrees | ±1.3 | ±0.5 | ±0.4 | ±0.4 | ±0.3 | ±0.2 |
| USLS, beampeak to 20° above beampeak, dB | 16 | 17 | 16 | 17 | 15 | 15 |
| Front-to-Back Total Power at 180° ± 30°, dB | 25 | 23 | 27 | 29 | 29 | 29 |
| CPR at Boresight, dB | 20 | 19 | 19 | 20 | 21 | 18 |
| CPR at Sector, dB | 12 | 10 | 12 | 10 | 8 | 6 |
Mechanical Specifications
| Wind Loading @ Velocity, frontal | 306.0 N @ 150 km/h (68.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, lateral | 258.0 N @ 150 km/h (58.0 lbf @ 150 km/h) |
| Wind Loading @ Velocity, maximum | 647.0 N @ 150 km/h (145.5 lbf @ 150 km/h) |
| Wind Loading @ Velocity, rear | 324.0 N @ 150 km/h (72.8 lbf @ 150 km/h) |
| Wind Speed, maximum | 241 km/h (150 mph) |
Packaging and Weights
| Width, packed | 460 mm | 18.11 in |
| Depth, packed | 350 mm | 13.78 in |
| Length, packed | 2000 mm | 78.74 in |
| Weight, gross | 44 kg | 97.003 lb |
Regulatory Compliance/Certifications
| Agency | Classification |
CE
|
Compliant with the relevant CE product directives |
ISO 9001:2015
|
Designed, manufactured and/or distributed under this quality management system |
| ROHS | Compliant/Exempted |
CHINA-ROHS
|
Above maximum concentration value |
| REACH-SVHC | Compliant as per SVHC revision on www.commscope.com/ProductCompliance |
| UK-ROHS | Compliant/Exempted |
General Specifications
| Antenna Type | Sector |
| Band | Multiband |
| Grounding Type | RF connector inner conductor and body grounded to reflector and mounting bracket |
| Performance Note | Outdoor usage |
| Radome Material | Fiberglass, UV resistant |
| Radiator Material | Aluminum | Low loss circuit board |
| Reflector Material | Aluminum |
| RF Connector Interface | 4.3-10 Female |
| RF Connector Location | Bottom |
| RF Connector Quantity, high band | 4 |
| RF Connector Quantity, low band | 4 |
| RF Connector Quantity, total | 8 |
Remote Electrical Tilt (RET) Information
| RET Interface | 8-pin DIN Female | 8-pin DIN Male |
| RET Interface, quantity | 1 female | 1 male |
| Input Voltage | 10–30 Vdc |
| Internal RET | High band (2) | Low band (2) |
| Power Consumption, idle state, maximum | 2 W |
| Power Consumption, normal conditions, maximum | 13 W |
| Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
| Width | 350 mm | 13.78 in |
| Depth | 208 mm | 8.189 in |
| Length | 1850 mm | 72.835 in |
| Net Weight, without mounting kit | 30.5 kg | 67.241 lb |
Electrical Specifications
| Impedance | 50 ohm |
| Operating Frequency Band | 694 – 862 MHz | 880 – 960 MHz | 1695 – 2690 MHz |
| Polarization | ±45° |
| Total Input Power, maximum | 800 W @ 50 °C |
Electrical Specifications
| Frequency Band, MHz | 694–862 | 880–960 | 1695–1920 | 1920–2180 | 2300–2500 | 2500–2690 |
| Gain, dBi | 15.2 | 15.5 | 18.2 | 18.9 | 18.8 | 18.8 |
| Beamwidth, Horizontal, degrees | 67 | 62 | 60 | 61 | 60 | 59 |
| Beamwidth, Vertical, degrees | 11.8 | 9.8 | 5.6 | 5 | 4.4 | 4.3 |
| Beam Tilt, degrees | 2–14 | 2–14 | 2–12 | 2–12 | 2–12 | 2–12 |
| USLS (First Lobe), dB | 16 | 19 | 19 | 20 | 18 | 19 |
| Front-to-Back Ratio at 180°, dB | 29 | 29 | 31 | 36 | 36 | 37 |
| Isolation, Cross Polarization, dB | 28 | 28 | 28 | 28 | 28 | 28 |
| Isolation, Inter-band, dB | 30 | 30 | 30 | 30 | 30 | 30 |
| VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc | -150 | -150 | -150 | -150 | -150 | -150 |
| Input Power per Port at 50°C, maximum, watts | 200 | 200 | 250 | 250 | 250 | 200 |
Electrical Specifications, BASTA
| Frequency Band, MHz | 694–862 | 880–960 | 1695–1920 | 1920–2180 | 2300–2500 | 2500–2690 |
| Gain by all Beam Tilts, average, dBi | 14.9 | 15.3 | 17.6 | 18.4 | 18.4 | 18.4 |
| Gain by all Beam Tilts Tolerance, dB | ±0.4 | ±0.3 | ±0.8 | ±0.5 | ±0.6 | ±0.7 |
| Gain by Beam Tilt, average, dBi | 2 ° | 14.9; 8 ° | 14.9;14 ° | 14.8 | 2 ° | 15.5; 8 ° | 15.3;14 ° | 15.0 | 2 ° | 17.3; 7 ° | 17.7;12 ° | 17.7 | 2 ° | 17.9; 7 ° | 18.5;12 ° | 18.5 | 2 ° | 18.0; 7 ° | 18.6;12 ° | 18.4 | 2 ° | 17.9; 7 ° | 18.6;12 ° | 18.4 |
| Beamwidth, Horizontal Tolerance, degrees | ±1.3 | ±2.6 | ±4.4 | ±3.2 | ±4.7 | ±3.2 |
| Beamwidth, Vertical Tolerance, degrees | ±1.3 | ±0.5 | ±0.4 | ±0.4 | ±0.3 | ±0.2 |
| USLS, beampeak to 20° above beampeak, dB | 16 | 17 | 16 | 17 | 15 | 15 |
| Front-to-Back Total Power at 180° ± 30°, dB | 25 | 23 | 27 | 29 | 29 | 29 |
| CPR at Boresight, dB | 20 | 19 | 19 | 20 | 21 | 18 |
| CPR at Sector, dB | 12 | 10 | 12 | 10 | 8 | 6 |
Mechanical Specifications
| Wind Loading @ Velocity, frontal | 306.0 N @ 150 km/h (68.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, lateral | 258.0 N @ 150 km/h (58.0 lbf @ 150 km/h) |
| Wind Loading @ Velocity, maximum | 647.0 N @ 150 km/h (145.5 lbf @ 150 km/h) |
| Wind Loading @ Velocity, rear | 324.0 N @ 150 km/h (72.8 lbf @ 150 km/h) |
| Wind Speed, maximum | 241 km/h (150 mph) |
Packaging and Weights
| Width, packed | 460 mm | 18.11 in |
| Depth, packed | 350 mm | 13.78 in |
| Length, packed | 2000 mm | 78.74 in |
| Weight, gross | 44 kg | 97.003 lb |
| Click on image to enlarge. |
Regulatory Compliance/Certifications
| Agency | Classification |
|
CE
|
Compliant with the relevant CE product directives |
|
ISO 9001:2015
|
Designed, manufactured and/or distributed under this quality management system |
| ROHS | Compliant/Exempted |
|
CHINA-ROHS
|
Above maximum concentration value |
| REACH-SVHC | Compliant as per SVHC revision on www.commscope.com/ProductCompliance |
| UK-ROHS | Compliant/Exempted |
Documentation & Downloads
Assembly Drawing
Installation Instruction
Product Information
Product Specification
Warranty
Assembly Drawing
Installation Instruction
Product Compliance Documentation
Product Information
Product Specification
Warranty
Related Products and Accessories
Included Products
Antennas
-
![]()
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Structural Support, Tools & Accessories
-
![]()
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
-
![]()
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Related Products
Antennas
-
![]()
800PIPEKIT-X Cluster Mounting Kit. Use for mounting multiple wide panel antennas to a single pole or stand. One kit mounts up to three antennas. Removeable spacers allow this kit to fit on poles measuring 3.5, 4.5 or 5.5 in. OD.
-
![]()
APS-XT Antenna Orientation and Location Sensing System
Structural Support, Tools & Accessories
-
![]()
800PIPEKIT-X Cluster Mounting Kit. Use for mounting multiple wide panel antennas to a single pole or stand. One kit mounts up to three antennas. Removeable spacers allow this kit to fit on poles measuring 3.5, 4.5 or 5.5 in. OD.
-
![]()
800PIPEKIT-X Cluster Mounting Kit. Use for mounting multiple wide panel antennas to a single pole or stand. One kit mounts up to three antennas. Removeable spacers allow this kit to fit on poles measuring 3.5, 4.5 or 5.5 in. OD.
Included Products
Antennas
-
![]()
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Structural Support, Tools & Accessories
-
![]()
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
-
![]()
BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Related Products
Antennas
-
![]()
800PIPEKIT-X Cluster Mounting Kit. Use for mounting multiple wide panel antennas to a single pole or stand. One kit mounts up to three antennas. Removeable spacers allow this kit to fit on poles measuring 3.5, 4.5 or 5.5 in. OD.
-
![]()
APS-XT Antenna Orientation and Location Sensing System
Structural Support, Tools & Accessories
-
![]()
800PIPEKIT-X Cluster Mounting Kit. Use for mounting multiple wide panel antennas to a single pole or stand. One kit mounts up to three antennas. Removeable spacers allow this kit to fit on poles measuring 3.5, 4.5 or 5.5 in. OD.
-
![]()
800PIPEKIT-X Cluster Mounting Kit. Use for mounting multiple wide panel antennas to a single pole or stand. One kit mounts up to three antennas. Removeable spacers allow this kit to fit on poles measuring 3.5, 4.5 or 5.5 in. OD.
Other Ways to Browse
